Description
Crescent Knives, Left & Right – Use with Beet Knife Shank Holder
Crescent Knives Description: High carbon, heat treated steel
- Bolt Hole Size: 3/8”
- Centers: 1-1/4” to 2”
- Description: 6” X 1/4” crescent hoe
- Weight/ea: 1.9 lbs
Part# CH06LR is a Set of Right and Left Crescent Knives to be attached to a Beet Knife Shank as Shown Below:
(Sold Separately)
To attach to the Part# BK58 Beet Knife Shank: (2) 3/8″ x 1 1/2″ Carriage Bolts w/ (2) Nuts & (2) Bolts
Fork is 1/2″ x 2″ steel welded to a 5/8″ x 2″Shank
Beet and/or banana knifing shanks are single offset staggered fork units with 6″ ID spacing between the knives.
Beet Knife Shank Holder Shown Below with the Crescent Knives
For Assembly – Just Attach the Part# BK58 Beet Knife Shank Holder with Part# CH06LR Crescent Knives to Part# S22Wood Flat Shank Clamp onto a Part# HT02-04-L4 2 x 2 Toolbar – Sold Separately
With Just 1 Hitch and a Toolbar, You Can Build Many Implements!
Heavy Duty – Up to 85 HP
Includes Pins
- Cat I Hitch Pins: Diameter .750″
- Useable Length 2.750″
- Overall Length 4.500″
WUNDERBAR 3 PT. HITCH DIMENSIONS:
17″ from Top Pin to Lower Pin
Upper Link is 3/4″
Lower Links are 7/8″
Pin to Pin – Center to Center – 26″-28
Spacer Bars, Toolbars & Attachments Sold Separately
Hill Potatoes & Build Rows to Keep Dirt Close to Crops by Adding Disc Hillers and Disc Hiller Clamps
Dig Potatoes by Adding a Shank, Shank Clamp and a High Sweep Furrower
By using 2 “Spacer Bars” to the Wunderbar Cat I Hitch and Adding an Additional Toolbar, You Can Make Your Own 2-Row Cultivator and More!
Wunderbar Cat I Hitch with Double Row Cultivator Set
Cultivate Crops by adding S-Tines, S-Tine Clamps and Sweeps
Our Wunderbar Cat I Hitch is Recommended for Use with our Components or Components that a Similar in Size and Function
Part #HT02-04-L4 Toolbar Sold Separately
One Toolbar, One Hitch and Create Many Implements in Just a Few Minutes!
Tools Needed:
1 5/16” Socket to snug up the Toolbar on the 3 Pt. Hitch
1 1/8 Socket to snug up the Disc Hiller Clamps to the toolbar
9/16” wrench to tighten up the Disc Hillers in the Disc Hiller Clamp
5/8” Wrench to snug up Flat Shank to the Flat Shank Clamp
¾” Wrench to snug up Flat Shank Foot Pieces
(2) 3/8” x 3” bolts and washers to affix the Furrower to the Foot Piece
9/16” Wrench to snug up the bolts to Foot Piece and Furrower
Snug up Elliptical Bolts on S-Tines with 9/16” wrench
3/8” x 3 Carriage bolts for S-Tine Clamps and 7/16” Nuts to fasten the S-Tine Clamps to the Toolbar
11/16” wrench to snug up the bolts on the S-Tine Clamps
Wowsers! Above is a pic submitted by David Mastin of New York.
Showing our CAT I 3 Pt. Hitch, 18″ Spacers, 6 Ft. Toolbars, our 5/8″ Shanks, and Straight Chisel Spikes.
David painted his toolbars John Deere Green. Quite impressive! Thanks, Dave for Sharing!
