Tender Plant Hoe Knives, Set of Left and Right – Use w/ Beet Knife Shank Holder
Tender Plant Hoe Knives come in a set of Left and Right knives which are 9 inches long
For Use in Weeding Closely to the Plant Row
The Tender Plant Hoe Knives attach to the Part# BK58 Beet Knife Shank with (2) 3/8″ x 1 1/2″ Carriage Bolts w/ (2) Nuts & (2) Bolts
Fork is 1/2″ x 2″ steel welded to a 5/8″ x 2″Shank
Part# BK58 Beet Knife Holder (Sold Separately)
Beet and/or banana knifing shanks are single offset staggered fork units
with 6″ ID spacing between the knives.
APPLICATION: The staggered fork configuration provides more room for shedding of trash and weed foliage between knives which in turn aids in the prevention of “dragging” out crops. Allows beet, crescent, tender hoe knives and/or banana knives to be mounted on existing cultivator bars with a single clamp. See our Flat Shank Clamp below.
Beet Knife Holder (Sold Separately)
For Assembly – Just Attach the Beet Knife Holder with Tender Plant Hoe Knives to a Part# S22Wood Flat Shank Clamp (Sold Separately) onto Part# HT02-04-L4 2 x 2 Toolbar (Sold Separately)
Then, put on Crescent Knives, Beet Knives or Tender Plant Hoe Knives to Cultivate Closely to Your Plant Row
With Just 1 Hitch and a Toolbar, You Can Build Many Implements!
Heavy Duty – Up to 85 HP
- Cat I Hitch Pins: Diameter .750″
- Useable Length 2.750″
- Overall Length 4.500″
WUNDERBAR 3 PT. HITCH DIMENSIONS:
17″ from Top Pin to Lower Pin
Upper Link is 3/4″
Lower Links are 7/8″
Pin to Pin – Center to Center – 26″-28
Spacer Bars, Toolbars & Attachments Sold Separately
Hill Potatoes & Build Rows to Keep Dirt Close to Crops by Adding Disc Hillers and Disc Hiller Clamps
Wunderbar Potato Plow Bundle w/ Wunderbar Cat I Hitch
Dig Potatoes by Adding a Shank, Shank Clamp and a High Sweep Furrower
By using 2 “Spacer Bars” to the Wunderbar Cat I Hitch and Adding an Additional Toolbar, You Can Make Your Own 2-Row Cultivator and More!
Cultivate Crops by adding S-Tines, S-Tine Clamps and Sweeps
Our Wunderbar Cat I Hitch is Recommended for Use with our Components or Components that a Similar in Size and Function
Part #HT02-04-L4 Toolbar Sold Separately
One Toolbar, One Hitch and Create Many Implements in Just a Few Minutes!
1 5/16” Socket to snug up the Toolbar on the 3 Pt. Hitch
1 1/8 Socket to snug up the Disc Hiller Clamps to the toolbar
9/16” wrench to tighten up the Disc Hillers in the Disc Hiller Clamp
5/8” Wrench to snug up Flat Shank to the Flat Shank Clamp
¾” Wrench to snug up Flat Shank Foot Pieces
(2) 3/8” x 3” bolts and washers to affix the Furrower to the Foot Piece
9/16” Wrench to snug up the bolts to Foot Piece and Furrower
Snug up Elliptical Bolts on S-Tines with 9/16” wrench
3/8” x 3 Carriage bolts for S-Tine Clamps and 7/16” Nuts to fasten the S-Tine Clamps to the Toolbar
11/16” wrench to snug up the bolts on the S-Tine Clamps
Wowsers! Above is a pic submitted by David Mastin of New York.
Showing our CAT I 3 Pt. Hitch, 18″ Spacers, 6 Ft. Toolbars, our 5/8″ Shanks, and Straight Chisel Spikes.
David painted his toolbars John Deere Green. Quite impressive! Thanks, Dave for Sharing!