Toolbar 2 X 2 X 1/4″ Wall X 4 Ft. Long Square Tube for 3 Pt. Hitch

Description

Toolbar 2 X 2 X 1/4″  Wall X 4 Ft. Long Square Tube for 3 Pt. Hitch, Unfinished

Toolbar 2 X 2 X 1/4″  Wall X 4 Ft. Long Square Tube for 3 Pt. Hitch comes standard as Unfinished, but  you can upgrade to a Painted Black Toolbar at checkout  as well as upgrade to a 6 Ft. Toolbar, however, there is an Add’l Cost for the Length, Weight & Oversize Shipping Upcharge

 Build Your Own Disc Hiller & Furrower, Cultivator, Middlebuster and So Much More with a 2 x 2 Toolbar!

Heavy Duty! Weighs 24 #’s!

Part# HT02-04-L4 2 Toolbar, 2 X 2 X 1/4″ Wall X 4 Ft. Long Square Tube for 3 Pt. Hitch Mounting  Comes Unfinished

6 Ft. Toolbar Can be Ordered in lieu of the 4 Ft. Toolbar at Check Out, however there is an Add’l Cost for the Length, Weight & Oversize Shipping Upcharge

Part#  HT02-04-L4 2 x 2 Toolbar for a Part# Cat I 2×2 Three Point Hitch 

It’s All About Versatility!

Paint the toolbar to match your tractor!

Or should you want a toolbar painted back, you may upgrade to a painted black toolbar at checkout.

---

With Just 1 Hitch and a Toolbar, You Can Build Many Implements!

Heavy Duty – Up to 85 HP

Includes Pins

• Cat I Hitch Pins:  Diameter .750″
• Useable Length 2.750″
• Overall Length 4.500″

WUNDERBAR 3 PT. HITCH DIMENSIONS:

17″ from Top Pin to Lower Pin
Upper Link is 3/4″
Lower Links are 7/8″
Pin to Pin – Center to Center –  26″-28

Spacer Bars, Toolbars & Attachments Sold Separately

Hill Potatoes & Build Rows to Keep Dirt Close to Crops by Adding Disc Hillers and Disc Hiller Clamps

Dig Potatoes by Adding a Shank, Shank Clamp and a High Sweep Furrower

By using 2 “Spacer Bars” to the  Wunderbar Cat I Hitch and Adding an Additional Toolbar, You Can Make Your Own 2-Row Cultivator and More!

Cultivate Crops by adding S-Tines, S-Tine Clamps and Sweeps

Our Wunderbar Cat I Hitch is Recommended for Use with our Components or Components that a Similar in Size and Function

One Toolbar, One Hitch and Create Many Implements in Just a Few Minutes!

Tools Needed:

1 5/16” Socket to snug up the Toolbar on the 3 Pt. Hitch

1 1/8 Socket to snug up the Disc Hiller Clamps to the toolbar

9/16” wrench to tighten up the Disc Hillers in the Disc Hiller Clamp

5/8” Wrench to snug up Flat Shank to the Flat Shank Clamp

¾” Wrench to snug up Flat Shank Foot Pieces

(2) 3/8” x 3” bolts and washers to affix the Furrower to the Foot Piece

9/16” Wrench to snug up the bolts to Foot Piece and Furrower

Snug up Elliptical Bolts on S-Tines  with 9/16” wrench

3/8” x 3 Carriage bolts for S-Tine Clamps and 7/16” Nuts  to fasten the S-Tine Clamps to the Toolbar

11/16” wrench to snug up the bolts on the S-Tine Clamps

Wowsers! Above is a pic submitted by David Mastin of New York.

Showing our CAT I 3 Pt. Hitch, 18″ Spacers, 6 Ft. Toolbars, our 5/8″ Shanks, and Straight Chisel Spikes.

David painted his toolbars John Deere Green.  Quite impressive! Thanks, Dave for Sharing!

You may also be interested in our 2 x 2 U-Bolt for the 2 x 2 Toolbar:

U5822 U-Bolt 5/8 x 2 x 2 for a 2″ Square Toolbar

You may also want Covering Chains to smooth out dirt.