Wunder Weeder with Poly Fingers for Inner-Row Weeding or Cultivating
Designed with the Produce Grower in mind, the Wunder Weeder with Poly Fingers for Inner-Row Weeding or Cultivating will fast become one of the growers’ prized gardening tools.
Made right here at Woodward Crossings in Central PA, the Woodward Crossings’ Wunder Weeder is our newest offering for use with the Wunderbar Module (see bottom of page).
Intended for small, young weeds, the Wunder Weeder beautifully rotates through the rows flicking out the unwanted growth with durable poly fingers.
Assembled with ball bearings, the Wunder Weeders provide a ground driven rotation removing small weeds and grasses near the plants.
The Wunder Weeder boasts a durable rugged 1 x 1 1/2″ wide 14″ long shank with (14) 13 1/2″ long poly fingers!
Woodward Crossings Wunder Weeder Specifications:
- Poly Fingers – 14
- Poly Fingers – 13 1/2″ in Length.
- Shank Bar – 1″ x 1 1/2″
- Shank Length – 14″
Sold Separately is the Clamp for the Wunder Weeders to clamp onto our Wunderbar Module or any 2 x 2 flat toolbar.
Wunder Weeder and Clamp on an Allis G (below)
Use Your Imagination!!
Check out our Wunderbar Module!
With Just 1 Hitch and a Toolbar, You Can Build Many Implements!
Heavy Duty – Up to 85 HP
- Cat I Hitch Pins: Diameter .750″
- Useable Length 2.750″
- Overall Length 4.500″
WUNDERBAR 3 PT. HITCH DIMENSIONS:
17″ from Top Pin to Lower Pin
Upper Link is 3/4″
Lower Links are 7/8″
Pin to Pin – Center to Center – 26″-28
Spacer Bars, Toolbars & Attachments Sold Separately
Hill Potatoes & Build Rows to Keep Dirt Close to Crops by Adding Disc Hillers and Disc Hiller Clamps
Wunderbar Potato Plow Bundle w/ Wunderbar Cat I Hitch
Dig Potatoes by Adding a Shank, Shank Clamp and a High Sweep Furrower
By using 2 “Spacer Bars” to the Wunderbar Cat I Hitch and Adding an Additional Toolbar, You Can Make Your Own 2-Row Cultivator and More!
Wunderbar Cat I Hitch with Double Row Cultivator Set
Cultivate Crops by adding S-Tines, S-Tine Clamps and Sweeps
Our Wunderbar Cat I Hitch is Recommended for Use with our Components or Components that a Similar in Size and Function
Part #HT02-04-L4 Toolbar Sold Separately
One Toolbar, One Hitch and Create Many Implements in Just a Few Minutes!
1 5/16” Socket to snug up the Toolbar on the 3 Pt. Hitch
1 1/8 Socket to snug up the Disc Hiller Clamps to the toolbar
9/16” wrench to tighten up the Disc Hillers in the Disc Hiller Clamp
5/8” Wrench to snug up Flat Shank to the Flat Shank Clamp
¾” Wrench to snug up Flat Shank Foot Pieces
(2) 3/8” x 3” bolts and washers to affix the Furrower to the Foot Piece
9/16” Wrench to snug up the bolts to Foot Piece and Furrower
Snug up Elliptical Bolts on S-Tines with 9/16” wrench
3/8” x 3 Carriage bolts for S-Tine Clamps and 7/16” Nuts to fasten the S-Tine Clamps to the Toolbar
11/16” wrench to snug up the bolts on the S-Tine Clamps
Wowsers! Above is a pic submitted by David Mastin of New York.
Showing our CAT I 3 Pt. Hitch, 18″ Spacers, 6 Ft. Toolbars, our 5/8″ Shanks, and Straight Chisel Spikes.
David painted his toolbars John Deere Green. Quite impressive! Thanks, Dave for Sharing!
Buy a Wunderbar Bundle – then –add a Set to your Bundle