Wunderbar Disc Hiller Set – Without Toolbar & Hitch
Use our Wunderbar Disc Hiller Set to Hill Potatoes & Build Rows to Keep Dirt Close to Crops and to Create Hills for Planting
Add the Wunderbar Disc Hiller Set to Part# CAT I 2×2 3 Pt. Wunderbar Hitch and Part# HT02-04-L4 2 x 2 x 1/4 wall – 4 Ft. Toolbar (Both Sold Separately)
Woodward Crossings Calls Their Module “Wunderbar” Because it’s Marvelously Wonderful!
Our Wunderbar “Sets” can be added to the Hitch and Toolbar to create a whole other piece of equipment.
Wunderbar Disc Hiller Set Part# DHS Includes:
(2) Part#R22Wood Disc Hiller Clamps
(2) Part#72H31752 16″ Disc Hillers
Note: Part# 72H33132 12″ Disc Hillers are available to order at Check Out
Heavy and Rugged!
Snug up Toolbar on the 3 Pt. Hitch with a 1 5/16″ Air Ratchet
Slide on the Disc Hiller Clamps and then Insert the Disc Hillers- Tighten Bolts.
Adding a “Set” to the Wunderbar Hitch and Toolbar, You Can Create Your Own Furrower, Tire Track Eraser, Weeder Fingers, Cultivator, Middlebuster and So Much More!
It’s All About Versatility!
With Just 1 Hitch and a Toolbar, You Can Build Many Implements!
Heavy Duty – Up to 85 HP
- Cat I Hitch Pins: Diameter .750″
- Useable Length 2.750″
- Overall Length 4.500″
WUNDERBAR 3 PT. HITCH DIMENSIONS:
17″ from Top Pin to Lower Pin
Upper Link is 3/4″
Lower Links are 7/8″
Pin to Pin – Center to Center – 26″-28
Spacer Bars, Toolbars & Attachments Sold Separately
Hill Potatoes & Build Rows to Keep Dirt Close to Crops by Adding Disc Hillers and Disc Hiller Clamps
Wunderbar Potato Plow Bundle w/ Wunderbar Cat I Hitch
Dig Potatoes by Adding a Shank, Shank Clamp and a High Sweep Furrower
By using 2 “Spacer Bars” to the Wunderbar Cat I Hitch and Adding an Additional Toolbar, You Can Make Your Own 2-Row Cultivator and More!
Wunderbar Cat I Hitch with Double Row Cultivator Set
Cultivate Crops by adding S-Tines, S-Tine Clamps and Sweeps
Our Wunderbar Cat I Hitch is Recommended for Use with our Components or Components that a Similar in Size and Function
Part #HT02-04-L4 Toolbar Sold Separately
One Toolbar, One Hitch and Create Many Implements in Just a Few Minutes!
1 5/16” Socket to snug up the Toolbar on the 3 Pt. Hitch
1 1/8 Socket to snug up the Disc Hiller Clamps to the toolbar
9/16” wrench to tighten up the Disc Hillers in the Disc Hiller Clamp
5/8” Wrench to snug up Flat Shank to the Flat Shank Clamp
¾” Wrench to snug up Flat Shank Foot Pieces
(2) 3/8” x 3” bolts and washers to affix the Furrower to the Foot Piece
9/16” Wrench to snug up the bolts to Foot Piece and Furrower
Snug up Elliptical Bolts on S-Tines with 9/16” wrench
3/8” x 3 Carriage bolts for S-Tine Clamps and 7/16” Nuts to fasten the S-Tine Clamps to the Toolbar
11/16” wrench to snug up the bolts on the S-Tine Clamps
Wowsers! Above is a pic submitted by David Mastin of New York.
Showing our CAT I 3 Pt. Hitch, 18″ Spacers, 6 Ft. Toolbars, our 5/8″ Shanks, and Straight Chisel Spikes.
David painted his toolbars John Deere Green. Quite impressive! Thanks, Dave for Sharing!
Buy a Wunderbar Bundle – then –add a Set to your Bundle